This will also cause a mode change if needed, if using multi-mode firmware. There is more on the "Multi Mode" product tab. This displays the selected pin you are configuring. You can select pins from here or from the main graphic. You can type text in here which will remind you of which device this pin is connected to. The test is saved with the configuration on the PC only and is not sent to the board.
Here you configure the selected pin as the required device type and assign values to it. You can select one of the radio buttons to define the pin as the following:. In the primary drop-down all possible keys are available plus macros defined separately see later. Note that the I-PAC sends key scan codes just like a keyboard. An upper-case key is a macro consisting of the Shift key plus the required character. If required, you can select a secondary keycode.
This is sent instead of the standard code when the I-PAC shift button is held. This is by default the Start1 button but can be changed.
In the "Config" tab, the setting can be changed to 4 values as required. The default is the "standard" setting. This value affects the rate at which the SAME input can be re-activated. Setting a low value will allow faster repeat of presses of the same button, but may also cause unwanted key repeat caused by switch bounce.
This is a specialized setting and should only be changed following testing with the specific switches being used. It does not affect overall performance because it only affects repeated action of the same input. This can be used in various ways. One method would be to copy the entire application to a different folder so you have two versions.
Another way would be to use only one version and either apply the switch or not. Care would be needed when saving and loading IPC files. First, the board is placed in firmware upgrade mode. Also a driver is installed on-the-fly if this is the first time an upgrade has been done on the PC.
This program will not detect the board unless it has been placed into upgrade mode from within WinIPAC. The units were designed around MAME and normally you would use a front-end menu for selecting games. But of course, as the I-PAC emulates a real keyboard without all the drawbacks you can use any PC application which uses keyboard input. You can use the fully programmable code sets of I-PAC to customise for any emulator or other application. Several popular front-end menus even have integrated support for downloading I-PAC codesets on-the-fly.
Using the key-code programming is entirely optional. When the board is shipped, all codes are automatically assigned to MAME standard keys. As many people have found, this makes installation very quick and easy. One method is to hack a keyboard, i. This is pretty unsatisfactory for several reasons: It takes ages to wire up as 2 wires need to be run to each switch. Extra buttons: With this solution, with some emulators you have to have extra buttons on the cabinet for functions such as "escape", "insert coin" etc.
Nobody likes drilling extra holes in their nice original arcade cab! Speed: Keyboard encoders use a scanning method. So each key is checked in sequence for a press or release. I-PAC does not use a matrix or scanning. Shifted function keys will do various functions ie press "1 player start" and "fire" and you will insert a coin. Press "1 player start" and "2 player start" and you will jump back to the menu. You can also use the MAME game config menus with shift buttons, ie tab and enter are shift joystick right and left.
The 1 player start button is always the shift button if you are using the standard MAME codes. In programmable mode you can assign any input to be the shift button and you can program all of the buttons to have shifted codes. The unique feature of the shift function is that it requires no dedicated extra button. When the board is shipped it contains all standard MAME codes including the shift codes mentioned above.
If you only ever use MAME and want a quick and easy install this will probably do for you. But if you need to, you can re-program as required, including "on the fly", and the board will remember your new settings. You may find you need to change the assignment of keys for other emulators or maybe you don't want to have the shift functions of the MAME code set. There is even a Mac version of the programming utility. There is third-party Linux programming utility support see Downloads page.
Click Here for older software versions for pre boards. Latest firmware files ver 1. Check the Multi-Mode tab on the product pages for more info. Before upgrading ensure you have the I-PAC shift functionality enabled otherwise mode switching will not work. The default is Start1 being the shift control. Also before upgrading to multi-mode firmware ensure the latest WinIPAC version is installed from the download page.
If the board comes up in Xinput mode after upgrading, this can be reset to standard keyboard by holding P1SW1 while connecting USB cable. Note Retropie does not work with this configuration. The standard multiMode version above enables one device type at a time on the host plus mouse and this is required for Retropie.
This version does not support Xinput. Unlike the Multi-Mode, this version automatically allocates each of the 2 game controllers on the respective side of the board so WinIPAC does not refer to player numbers, these are defined by the board markings.
I-PAC 4 only supports 2 game controllers. Click here to download all mixed-mode firmware versions. Click here to download the new version for Intel Macs. Linux software utilities are available. These cover several of our products and are being added-to. Please note we are not able to provide direct support for these utilities:.
Linux Library and command line utilities developed by Katie Snow. When this is done, keys configured as keyboard keys will respond in Mode 1, Keys configured as gamepad keys respond in modes 4 and 5.
Note this feature allows the entire 2-player panel to be configured as a one-player game controller if required, implementing every possible control. These will function in modes 1 and 4. When powered on, the LED will stay lit once the board has passed self-test and detected by the host system.
When switching modes, the LED will flash off, the number of times according to the mode number selected, after the 10 second period. This is the recommended method of mode switching if it is required to regularly switch modes.
Owing to the limitations imposed by the Xinput protocol, the following are NOT supported in Xinput modes but are supported in keyboard and Directinput modes:.
Note that a mode switch is essentially the same as unplugging a USB device and plugging in a different one, into the same port. It will take the host PC up to 30 seconds to notice this and initialize the new device. If hotkey mode switching fails to work, check that Start1 or another connection is configured as an I-PAC shift control.
The board can be rest back into keyboard Mode 0 by pressing and holding the P1SW1 button on power up. This will work irrespective of the current board mode or input configuration. Note it must be a hard power-up or plug-in of the USB cable. My Account. Orders Wish list Track my order s. Track my order s. Sign in Register Email. Password Forgot your password? Register for a new account. Sign in. Remember me. Altiris eXpress. PC Transplant. Asset Tracking and Security. Password Security.
Fault Notification and Recovery. Software Updating and Management. Remote ROM Flash. Remote Security Management. Remote Wakeup and Remote Shutdown. Replicating Your Setup. Dual-State Power Button. Power Management. World Wide Web Site. Building Blocks and Partners. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
To reduce the risk of electrical shock, connect your Personal Computer only to a grounded earthed electrical outlet that is easily accessible at all times. One of these controllers is dedicated exclusively to a new, full-speed Universal Serial Bus USB connector shown on the previous page. The other five USB connectors share the second controller. Microsoft Windows 98 and Windows NT 4. Connect the monitor, mouse, and keyboard cables. If you use a network, connect the network cable to the Ethernet RJ Connector.
For easy setup, Compaq has color-coded the cables and rear panel connectors. A USB mouse or keyboard may be connected to any of the available USB connectors; however, you may want to reserve the dedicated, full-speed USB connector for USB devices, such as digital cameras, scanners, or networking devices that demand the extra speed for enhanced performance.
Doing so may cause errors and may prevent the operating system from installing properly. The grounding plug is an important safety feature. Press the power button to turn on the personal computer. The first time you turn on the Personal Computer, the operating system is installed automatically. This process takes about 10 minutes, depending on which operating system is being installed. Carefully read and follow the instructions that appear on the screen to complete the installation.
Turning off the Personal Computer during the installation process might damage the software that runs the Personal Computer. When the Welcome to Windows screen is displayed, the Windows installation process is complete.
You can manually select or change the monitor brand, model, refresh rates, color, resolution, and power management settings. Select the Display icon in the Windows Control Panel to change display settings, or refer to the online documentation provided with the graphics controller utility.
To protect your software from loss or damage, you should keep a backup copy of all system software, applications, and related files stored on your hard drive. Refer to your operating system or backup utility documentation for instructions on making backup copies of your data files.
This can be extremely helpful in the event of hard drive failure or corruption. Additional support software for specific models may be downloaded from www.
Carefully read and follow all instructions that appear on the screen. The Restore CD will erase all files from the hard drive before restoring the original operating system, Internet browser, and NIC or modem drivers. You may need to use the keyboard to make selections during the system restore process.
For questions about or problems with this CD, please contact Compaq customer service. Be sure to register your new personal computer with Compaq. Registration establishes a record of ownership and gives you an opportunity to receive product announcements, updates, and other communications periodically, if you choose to do so. Registration is easy—just visit the Compaq Web site at www. To properly turn off the personal computer, first shut down the operating system software.
In Windows NT Workstation 4. However, in the default configuration of Windows 98, Windows Professional, or Windows Millenium, pressing the power button does not turn off the power, but causes the Personal Computer to enter a low-power state. This allows you to conserve energy without closing software applications; later, you can start using the computer immediately, without having to restart the operating system and without any data loss.
If the power button is pressed and held in for four seconds, power to the Personal Computer will turn off completely. In addition to the standard keyboard keys, the Compaq Easy Access Keyboard offers eight Easy Access Buttons that make accessing your favorite Web sites, services, and applications easier and faster.
Driver detection is temporarily unavailable. Please try again later. HP has scanned your product but currently has no suggestions for driver updates. The list of all available drivers for your product is shown above. HP encountered an error while trying to scan your product. Please verify your product is powered on and connected, then try again in a few minutes. Or, view all available drivers for your product below. Not sure which drivers to choose? Let HP identify any out-of-date or missing drivers and software.
Check now. The list of recommended drivers for your product has not changed since the last time you visited this page. Select registration option. Error: Javascript is disabled in this browser. This page requires Javascript. Modify your browser's settings to allow Javascript to execute. See your browser's documentation for specific instructions. HP Customer Support. Select your model.
How does HP install software and gather data? Search all support. Search help. Tips for better search results Ensure correct spelling and spacing - Examples: "paper jam" Use product model name: - Examples: laserjet pro p, DeskJet For HP products a product number. Loading Results.
Apache Log4j Update Please see this document here for current information regarding the Apache Log4j vulnerability. Need Windows 11 help? Product Homepage. Software and drivers for Choose a different product Choose a different OS. Download and Install Assistant. Don't ask again. Ok, get started. No thanks, I will download and install manually. Solution and Diagnostic Data Collection. Change preferred operating system Select preferred operating system. If you wish to see solutions related to another OS, please select the preferred operating system and version and choose 'Change' Select an operating system and version to see available software for this product.
Is my Windows version bit or bit? I don't see my operating system. Detected operating system: Selected operating system: Select your operating system and version , Change.
0コメント